Seachem Prime vs API Stress Coat

TankAndFin is reader-supported. If you buy through our links we may earn a commission at no extra cost to you. As an Amazon Associate we earn from qualifying purchases. Disclosure.
This comparison is built from the makers' own pages. We haven't tested either conditioner.
Side by side
| Seachem Prime | API Stress Coat | |
|---|---|---|
| Chlorine and chloramine | Removes both | Removes both |
| Ammonia | Detoxifies (Seachem's claim) | Not claimed |
| Nitrite and nitrate | Detoxifies (Seachem's claim) | Not claimed |
| Heavy metals | Detoxifies at typical tap levels (listing) | Detoxifies (API) |
| Slime coat | Not claimed | Aloe vera; "replaces the natural secretion of slime" |
| Dose | 5 mL per 50 US gal | 5 mL per 10 gal; double to repair fins |
| During cycling | "Will not halt your cycling process" | "Does not affect the biological filter" |
| pH | "Will not impact pH" | Doesn't affect pH (API FAQ) |
Dosing by tank size
Both labels give one dose and leave the division to you. Here it is worked out for common tank sizes, from Seachem's "1 capful (5 mL) for each 200 L (50 US gallons) of new water" and API's "5 ml per 10 gallons of aquarium water." The arithmetic is ours.
| Water treated | Seachem Prime | API Stress Coat | Stress Coat, double dose |
|---|---|---|---|
| 5 gallons | 0.5 mL | 2.5 mL | 5 mL |
| 10 gallons | 1 mL | 5 mL | 10 mL |
| 20 gallons | 2 mL | 10 mL | 20 mL |
| 29 gallons | 2.9 mL | 14.5 mL | 29 mL |
| 40 gallons | 4 mL | 20 mL | 40 mL |
| 55 gallons | 5.5 mL | 27.5 mL | 55 mL |
| 75 gallons | 7.5 mL | 37.5 mL | 75 mL |
- Which volume to use. Seachem says Prime "may be added to aquarium directly, but better if added to new water first. If adding directly to aquarium, base dose on aquarium volume." API says to dose Stress Coat for the new water when you're dechlorinating, and for the whole aquarium when a fish is recovering from injury or disease. So a 25% change on a 20 gallon tank is 5 gallons of new water: 0.5 mL of Prime in the bucket, or 2 mL if it goes straight into the tank.
- Measuring small doses. Seachem notes that "each cap thread is approximately 1 mL," which gets you close on a 10 gallon tank. Below that, a 1 mL syringe or pipette is easier than the cap.
- Stress Coat's double dose is API's direction "to replace slime coat and to repair damaged skin and fins."
- Prime's larger doses. Seachem allows a double dose for exceptionally high chloramine and up to 5 times the normal dose to detoxify nitrite in an emergency, and says it can be dosed every 24 to 48 hours.
Prime works out to 0.1 mL per gallon and Stress Coat to 0.5 mL per gallon, so a bottle of Prime treats five times the water of the same size bottle of Stress Coat at the standard dose. For your tank's real volume, see the aquarium volume calculator.
The chloramine question
UF says chloramine "is a combination of chlorine and ammonia," and Seachem says breaking it leaves ammonia ("chloramine minus chlorine = ammonia"). API's page says tap water contains "chlorine, chloramines and ammonia," but only Prime claims to detoxify ammonia. Seachem says Prime binds those compounds "for up to 48 hours" until the filter's bacteria handle them. These are the maker's claims; we haven't found independent testing of them, and a conditioner doesn't replace a cycled filter or a water change when ammonia shows up.
Notes
- Seachem warns that Nessler-type ammonia kits won't read correctly with Prime; with salicylate kits, read right away. See test kits.
- Seachem allows a double dose for very high chloramine and up to 5x for emergency nitrite detox; use half dose above 86°F if chlorine or ammonia is low.
- API says Stress Coat isn't recommended with a protein skimmer (a saltwater item).
The picks
Seachem Prime (250 mL)
- Listing says it removes chlorine and chloramine
- Seachem says it also detoxifies ammonia, nitrite and nitrate (maker's claim)
- 5 mL treats 50 US gallons of new water
Seachem Prime (500 mL)
- Larger bottle of the same conditioner
- 5 mL per 50 US gallons of new water
API Stress Coat (16 oz)
- Listing says it makes tap water safe
- Aloe vera to help replace the slime coat
- 5 mL per 10 gallons; double dose for damaged fins
More in water conditioners.
FAQ
What is the difference between Seachem Prime and API Stress Coat?
Both remove chlorine and chloramine. Seachem says Prime also detoxifies ammonia, nitrite and nitrate; API says Stress Coat detoxifies heavy metals and adds aloe vera to help replace the slime coat.
Which is more concentrated?
Seachem doses Prime at 5 mL per 50 US gallons; API doses Stress Coat at 5 mL per 10 gallons.
Does either stop cycling?
Seachem says Prime 'will not halt your cycling process.' API says Stress Coat does not affect the biological filter.
How much Seachem Prime per gallon?
Seachem's label dose is 1 capful (5 mL) for each 50 US gallons of new water, which works out to 0.1 mL per gallon: 1 mL for 10 gallons and 2 mL for 20. Seachem notes each cap thread is approximately 1 mL. The per-gallon arithmetic is ours.